Description
This wiper linkage is a direct bolt-on replacement for the Toyota Corolla (2003-2008). It carries OE reference 85150-B2090 and mounts to the original fixing points, so no drilling or adapter plates are needed.
Uneven wiping, a blade that lags on one side, or a knock on every pass usually traces back to worn pivots rather than the motor. If the linkage is left in place, the extra load is passed on to the motor and gearbox.
Vehicles this wiper linkage fits
| Make / model | Model years |
|---|---|
| Toyota Corolla | 2003-2008 |
Replaces OE number: 85150-B2090. If the number on your old linkage matches, this is the correct replacement.
Corolla 2003-2008 (85150-B2090): the volume Corolla linkage
This reference covers the high-volume Corolla generation that ran across Asia, the Middle East and Australasia. Because the car was everywhere, the linkage is one of our steady production items — and because these cars run long past their first decade, the linkage is usually a wear replacement, not an accident part.
- High mileage equals worn bushes. Most of these cars are on their second or third linkage by now.
- Dusty-market cars fail earliest. Grit past the cowl seal grinds the pivots; clear the drain and seals while the assembly is out.
- Two Corolla references share this era. Confirm against the stamped number — see the FAQ.
- Motor and crank reused. Assembly ships as rods, pivots and bracket.
Ordering checks
| Check | What to look for |
|---|---|
| OE number | 85150-B2090 on the old assembly — also 85150B2090 |
| Which Corolla | This era has sibling references (see 85150-1A030); the stamped number decides |
| Market | Australasian and Gulf-market cars share this reference; confirm with a photo if unsure |
| Arm marks | Tape the arms before removal |
Why the original part fails
On a high-mileage vehicle the linkage outlives the bushings inside it. Once a pivot stiffens, every sweep pulls harder on the motor, and the wiper arm timing drifts out of position.
- POM bushings, DuPont grade — The original soft bushings wear oval and let the pivot move off-centre. A harder, dimensionally stable bushing keeps the clearance the linkage was designed with.
- Brass bearings at the pivot pins — Carries the load at the point where the factory part scores, so service life is not limited by a single wear surface.
- Aluminium pivot arms — Adds stiffness to the linkage under load — this is what stops the assembly flexing and skipping.
- Galvanised and coated steel — Water from the windscreen drains straight over this area. Coated rods and brackets resist rust and seizing in wet climates.
- Pre-greased on assembly — The unit goes in ready to run, so there is no extra greasing step during fitting.
Specification
| OE number | 85150-B2090 |
|---|---|
| Vehicle | Toyota Corolla (2003-2008) |
| Bushings | POM (DuPont grade) with brass bearings |
| Pivot arms | Aluminium, re-engineered design |
| Finish | Galvanised and coated, anti-rust |
| Mounting | Direct bolt-on to original points |
| Greasing | Pre-greased at assembly |
| Testing | 100% inspected before shipment |
| Packing | Neutral carton or customer-branded |
| Warranty | 12 months |
Symptom to cause
| Symptom on the car | What is worn | Does this part fix it? |
|---|---|---|
| Arms out of step | Oval bush | Yes |
| Knock on reversal | Pivot pin play | Yes |
| Slow sweep under rain load | Gritty pivots loading the motor | Yes |
| Streaks with even arc | Blades | No |
Installation outline
- Battery off; arms marked at park.
- Arm caps and nuts off; arms pulled with a puller.
- Cowl trim removed; check the drain and seals while open.
- Bracket unbolted; assembly out; crank transferred from the motor.
- New assembly seated; bracket bolts evened.
- Arms to the marks; cycle tested; park corrected if needed.
Full procedure: how to replace a wiper linkage on your car.
Frequently asked questions
How do I confirm this Toyota Corolla linkage is the right part?
Match the OE reference 85150-B2090 against the number stamped or printed on your original linkage. If your part carries a superseded number, send us a photo of it and we will confirm the match before you order.
Is the wiper motor included in this listing?
This listing covers the linkage itself. Several of our linkages are also available as a linkage-with-motor assembly — tell us the vehicle and we will quote both options.
Can you supply this in bulk for distribution?
Yes. This is a volume part for the aftermarket and we supply importers, distributors and workshop chains with mixed container loads. Urgent orders are accepted and samples can be arranged.
There are two Corolla references for this era — which is mine?
The stamped number on the old assembly is the only reliable key: 85150-B2090 or 85150-1A030. Send a photo of the stamping if the number is worn away.
Is a 20-year-old Corolla worth a new linkage?
For markets where these cars are still daily transport, yes — that is exactly why we keep the reference in production.
Request a quote
Send us the OE number, the quantity you need and your destination port, and we will come back with price, MOQ and lead time. If you are sourcing a range of wiper linkages rather than a single part, ask for our full cross-reference list — we cover VW, Audi, Seat, Skoda, Ford, Toyota, Honda, Hyundai, Nissan and Opel applications.
Produced on our own line, OE cross-referenced — see distributor terms. Mechanism background: how a wiper linkage works.
Related wiper linkages and vehicle series
This Toyota Corolla 2003-2008 assembly is part of our Toyota Series wiper linkages range. Also stocked in the same series: Toyota Tacoma 1996-2004 wiper linkage (85150-04020) and Toyota Paseo 1996-1999 wiper linkage (85150-16520). For fitment guidance and fault diagnosis, see how a wiper linkage works. Every assembly ships with its OE cross-reference, so you can order by the number stamped on the old unit.






Reviews
There are no reviews yet.