MR388040 Windshield Wiper Linkage for Mitsubishi Montero 2001-2006

Brand-new OE-quality wiper linkage assembly for Mitsubishi Montero 2001-2006 (replaces OE MR388040). Supplied complete with links, pivots and crank arm, and it bolts onto the factory mounting points using the original wiper motor. Factory-direct wholesale supply for importers and distributors — MOQ 10 pcs.

Description

OE MR388040 — this wiper linkage is built as a straight swap for the original assembly on the Mitsubishi Montero (2001-2006). It reuses the factory mounting points and the original wiper motor.

Made by Ruian Fente Auto Parts in Zhejiang, China — we have run our own wiper-linkage line since 2012, so this reference is current production rather than old stock.

On a high-mileage vehicle the linkage outlives the bushings inside it. Once a pivot stiffens, every sweep pulls harder on the motor, and the wiper arm timing drifts out of position.

Vehicles this wiper linkage fits

Make / model Model years
Mitsubishi Montero 2001-2006

Replaces OE number: MR388040. If the number on your old linkage matches, this is the correct replacement.

Montero 2001-2006 fitment notes

The Montero uses a long, widely spaced linkage because of the size of the windscreen, and the two pivots sit far apart under a deep cowl. That layout is why a worn pivot on one side shows up so clearly: the arms drift out of step long before either one stops working.

  • Mud and salt reach the pivots. On vehicles used off-road or in winter markets, grit works past the cowl seal and grinds the bushing. A dry, gritty pivot is the first thing to check when the arms start to lag.
  • Long rods amplify play. A millimetre of clearance at the pivot becomes visible sweep error at the blade tip, so a small wear item reads as a big fault.
  • Bracket corrosion. The mounting points sit in a water path. Check the bracket and the bulkhead fixings before ordering — a rusted captive nut turns a two-hour job into a welding job.
  • Motor not included. The assembly is rods, pivots and brackets; the original motor and crank are reused.

Before you order

Check What to look for
OE number MR388040 on the old linkage — also supplied as MR388040 without separators
Model year 2001-2006 Montero. Confirm the year on the plate rather than the registration date
Bracket condition Look for rust around the mounting bolts and the bulkhead captive nuts
Arm position Mark both arms before removal; the linkage has no timing marks

Why the original part fails

Uneven wiping, a blade that lags on one side, or a knock on every pass usually traces back to worn pivots rather than the motor. If the linkage is left in place, the extra load is passed on to the motor and gearbox.

  • POM (acetal) bushings — The original soft bushings wear oval and let the pivot move off-centre. A harder, dimensionally stable bushing keeps the clearance the linkage was designed with.
  • Brass bearings at the pivot pins — Carries the load at the point where the factory part scores, so service life is not limited by a single wear surface.
  • Aluminium pivot arms — Adds stiffness to the linkage under load — this is what stops the assembly flexing and skipping.
  • Galvanised and coated steel — Water from the windscreen drains straight over this area. Coated rods and brackets resist rust and seizing in wet climates.
  • Pre-greased on assembly — The unit goes in ready to run, so there is no extra greasing step during fitting.

Specification

OE number MR388040
Vehicle Mitsubishi Montero (2001-2006)
Bushings POM (acetal) bushings with brass bearings
Pivot arms Aluminium pivot arms
Finish Galvanised and coated, anti-rust
Mounting Direct bolt-on to original points
Greasing Pre-greased at assembly
Testing Batch inspected for pivot play and sweep before packing
Packing Neutral carton, 10-20 pcs per carton, or customer-branded
Warranty 12 months

Faults this assembly resolves

Symptom on the car What is worn Does this part fix it?
Arms drift out of step, one lags on the return stroke Grit in one pivot bushing Yes — both pivots arrive new
Grinding or squeal from the cowl Dry spindle bearing Yes
Wiper sweep hesitates under load Seized joint raising motor current Yes, if the motor is still healthy
Blade leaves an unwiped band at the tip Arm spring or blade No — check arm and blade first

Fitting outline

  1. Battery off, arms tape-marked at their park position.
  2. Remove the arm nuts and pull both arms with a puller — the spindles are long and often tight.
  3. Take off the cowl cover, which on this vehicle is deep and clips along its full length.
  4. Unbolt the bracket at both ends and lift the assembly out without bending the rods.
  5. Transfer the crank from the original motor, then fit the new assembly and tighten the bracket evenly.
  6. Refit the arms to the marks and check the sweep across the full screen before the trim goes back on.

Step-by-step photographs: how to replace a wiper linkage on your car.

Frequently asked questions

What is the usual lead time?

Standard production runs 7-30 days from deposit, depending on quantity and whether you need neutral or branded packing. Sample orders ship within 7 days. Send the quantity and your destination port and we will confirm the schedule in the quotation.

Do you cover other models from the same platform?

Very often yes — several vehicles share the same linkage. If you tell us the models you buy for, we will check the full cross-reference and quote each reference separately.

How do I confirm this Mitsubishi Montero linkage is the right part?

Match the OE reference MR388040 against the number stamped or printed on your original linkage. If your part carries a superseded number, send us a photo of it and we will confirm the match before you order.

Will this fit both the three-door and five-door Montero?

The linkage reference is shared across the 2001-2006 range in our catalogue, but body variants differ by market. Send the model year and a photo of the old assembly and we will confirm before shipping.

Do you supply the bracket separately?

No. The bracket, rods and pivots are supplied as one assembly, because the geometry depends on all three being matched. Bushings alone are not sold either — a scored pin cannot be reliably re-bushed in the field.

Request a quote

Send us the OE number, the quantity you need and your destination port, and we will come back with price, MOQ and lead time. If you are sourcing a range rather than a single part, ask for the full cross-reference list — our catalogues are grouped into nine vehicle series (VW, Korea, American, Toyota, Honda, Nissan, Jeep/Mitsubishi/Subaru, Peugeot/Renault and Mazda), and one enquiry can cover several of them.

Manufactured and packed on our own line — specifications, MOQ and OEM options. For the mechanism behind the fault, see how a wiper linkage works.

Related wiper linkages and vehicle series

This Mitsubishi Montero 2001-2006 assembly is part of our Jeep Mitsubishi Subaru Series wiper linkages range. Also stocked in the same series: Mitsubishi Outlander 2003-2006 wiper linkage (MR971836) and Mitsubishi Outlander 2007-2008 wiper linkage (8251A031). For fitment guidance and fault diagnosis, see diagnosing wiper linkage problems. Every assembly ships with its OE cross-reference, so you can order by the number stamped on the old unit.

Additional information

Position

Front

Material

Aluminium + POM bushings

Warranty:

12 months

Minimum Order Quantity:

10 pcs

Packaging Details:

Carton of 10-20 pcs depending on size

Delivery Time:

7-30 days

Payment Terms:

T/T 30% deposit, balance before shipment

Place of Origin:

Made in China

Model Number:

602-811, MR388040

Reviews

There are no reviews yet.

Be the first to review “MR388040 Windshield Wiper Linkage for Mitsubishi Montero 2001-2006”

Your email address will not be published. Required fields are marked *

sixteen − 14 =

Ask For A Quick Quote

We will contact you within 1 working day, please pay attention to the email with the suffix “@fengteautoparts.com”.