Description
This wiper linkage is a direct bolt-on replacement for the Honda CRV (2007-2011). It carries OE reference 76530-SWA-A01 and mounts to the original fixing points, so no drilling or adapter plates are needed.
The failure mode is predictable — a binding pivot, a rusty rod end or cracked plastic bushing. Replacing the whole assembly is normally quicker and safer than pressing in new bushings on a scored pin.
Vehicles this wiper linkage fits
| Make / model | Model years |
|---|---|
| Honda CRV | 2007-2011 |
Replaces OE number: 76530-SWA-A01. If the number on your old linkage matches, this is the correct replacement.
CR-V 2007-2011: a large screen, long arms, hard work
The third-generation CR-V carries one of the largest windshields in the Honda range, and the linkage arms are long to match. Long arms magnify every fraction of play at the pivot into a visible sweep error at the blade tip, which is why CR-V owners notice linkage wear earlier than sedan owners do.
- Long arms load the pivots heavily. The same wear that a Civic tolerates for months shows up on a CR-V as a visible unwiped band within weeks.
- The cowl panel is clipped along its full length. It comes off with basic tools, but the clips are brittle at this age — budget for replacements.
- Pivot bearings dry out before they wear. Heat cycles in the cowl bake out the grease; the first symptom is often stiffness at cold start, not play.
- The motor is reused. Rods, pivots and bracket only — the motor, crank and connector transfer from the old unit.
Ordering checks
| Check | What to look for |
|---|---|
| OE number | 76530-SWA-A01 stamped on the old linkage — also 76530SWAA01 without hyphens |
| Generation | 2007-2011 CR-V. The 2012-onward model takes a different reference — confirm the year on the plate |
| Motor crank | Confirm the motor is being reused; the crank pin transfers to the new linkage |
| Arm position | Mark both arms before removal; long arms make even a small park error obvious on the glass |
Why the original part fails
Most failures on this type of assembly start at the pivots: the bushings dry out, water works into the joint and the pin starts to seize. The symptom shows up first as a smeared arc at the edge of the screen.
- POM bushings, DuPont grade — The original soft bushings wear oval and let the pivot move off-centre. A harder, dimensionally stable bushing keeps the clearance the linkage was designed with.
- Brass bearings at the pivot pins — Carries the load at the point where the factory part scores, so service life is not limited by a single wear surface.
- Aluminium pivot arms — Adds stiffness to the linkage under load — this is what stops the assembly flexing and skipping.
- Galvanised and coated steel — Water from the windscreen drains straight over this area. Coated rods and brackets resist rust and seizing in wet climates.
- Pre-greased on assembly — The unit goes in ready to run, so there is no extra greasing step during fitting.
Specification
| OE number | 76530-SWA-A01 |
|---|---|
| Vehicle | Honda CRV (2007-2011) |
| Bushings | POM (DuPont grade) with brass bearings |
| Pivot arms | Aluminium, re-engineered design |
| Finish | Galvanised and coated, anti-rust |
| Mounting | Direct bolt-on to original points |
| Greasing | Pre-greased at assembly |
| Testing | 100% inspected before shipment |
| Packing | Neutral carton or customer-branded |
| Warranty | 12 months |
What this assembly resolves
| Symptom on the car | What is worn | Does this part fix it? |
|---|---|---|
| Passenger arm lags on the return stroke | Worn bushing in that pivot | Yes — both pivots arrive new |
| Wipers stiff or slow at cold start, then normal | Dried grease in the pivots | Yes — new assembly is packed for life |
| Clunk when the wipers reverse | Worn pins or loose bracket bolts | Yes |
| Unwiped band at the tip, arc is even | Arm spring or blade | No — check arm and blade first |
Fitting outline
- Battery off; tape-mark the park position of both arms.
- Arm caps off, nuts undone, arms drawn with a puller.
- Remove the cowl panel and the wiper-well trim to expose the bracket.
- Unbolt the bracket, lift the assembly out and transfer the crank from the motor.
- Fit the new assembly and tighten the bracket across all fixings so the pivots sit square.
- Refit the arms to the marks, cycle the wipers and correct the park position if the arms sit high.
Photographic walk-through: replacing a wiper linkage.
Frequently asked questions
How do I confirm this Honda CRV linkage is the right part?
Match the OE reference 76530-SWA-A01 against the number stamped or printed on your original linkage. If your part carries a superseded number, send us a photo of it and we will confirm the match before you order.
Is the wiper motor included in this listing?
This listing covers the linkage itself. Several of our linkages are also available as a linkage-with-motor assembly — tell us the vehicle and we will quote both options.
Can you supply this in bulk for distribution?
Yes. This is a volume part for the aftermarket and we supply importers, distributors and workshop chains with mixed container loads. Urgent orders are accepted and samples can be arranged.
Will this fit the 2012-2016 CR-V?
No. The 2012-onward model uses a different linkage reference and a different motor interface. Send the model year and we will quote the correct number.
Do I need to remove the front bumper for access?
No. On the 2007-2011 CR-V the whole job is done from the cowl: arms off, cowl panel off, bracket unbolted. Bumper removal is a European-car habit, not a Honda one.
Request a quote
Send us the OE number, the quantity you need and your destination port, and we will come back with price, MOQ and lead time. If you are sourcing a range of wiper linkages rather than a single part, ask for our full cross-reference list — we cover VW, Audi, Seat, Skoda, Ford, Toyota, Honda, Hyundai, Nissan and Opel applications.
Made on our own line in Zhejiang and shipped factory-direct — details of MOQ, lead time and OEM packaging. If you are diagnosing rather than replacing, start with how the linkage mechanism works.
Related wiper linkages and vehicle series
This Honda CRV 2007-2011 assembly is part of our Honda Series wiper linkages range. Also stocked in the same series: Honda Accord 1998-2002 wiper linkage (76530-S84-A01) and Honda Accord 2003-2007 wiper linkage (76530-SDA-A01). For fitment guidance and fault diagnosis, see how to replace a wiper linkage. Every assembly ships with its OE cross-reference, so you can order by the number stamped on the old unit.












Reviews
There are no reviews yet.