Description
OE 85160-95J00 — this wiper linkage is built as a straight swap for the original assembly on the Toyota Hiace (1983-1989). It reuses the factory mounting points and the original wiper motor.
Uneven wiping, a blade that lags on one side, or a knock on every pass usually traces back to worn pivots rather than the motor. If the linkage is left in place, the extra load is passed on to the motor and gearbox.
Vehicles this wiper linkage fits
| Make / model | Model years |
|---|---|
| Toyota Hiace | – |
Replaces OE number: 85160-95J00. If the number on your old linkage matches, this is the correct replacement.
Hiace H50 (1983-1991): the vintage van reference
This is the early Hiace generation — a reference we keep in production because these vans are still working across Africa, South Asia and the Pacific. Everything about the job is “old van”: seized spindles, brittle trim, and a linkage that has probably been patched before.
- Forty-year-old spindles seize hard. A proper puller and penetrating oil are not optional.
- Previous repairs are common. Check the rods are straight and the crank is the original type before ordering.
- Current-spec bushes. Our bushings are new material — a real upgrade over any surviving original.
- Motor reused. Rods, pivots and bracket supplied; the crank transfers from the original motor.
Confirm before ordering
| Check | What to look for |
|---|---|
| OE number | 85160-95J00 on the old assembly — also 8516095J00 |
| Generation | 1983-1991 H50. The 1992-2004 van takes 85160-95J03 — a different reference |
| Previous repairs | Inspect rods and crank for non-original parts |
| Arm marks | Tape both arms before removal |
Why the original part fails
On a high-mileage vehicle the linkage outlives the bushings inside it. Once a pivot stiffens, every sweep pulls harder on the motor, and the wiper arm timing drifts out of position.
- POM bushings, DuPont grade — The original soft bushings wear oval and let the pivot move off-centre. A harder, dimensionally stable bushing keeps the clearance the linkage was designed with.
- Brass bearings at the pivot pins — Carries the load at the point where the factory part scores, so service life is not limited by a single wear surface.
- Aluminium pivot arms — Adds stiffness to the linkage under load — this is what stops the assembly flexing and skipping.
- Galvanised and coated steel — Water from the windscreen drains straight over this area. Coated rods and brackets resist rust and seizing in wet climates.
- Pre-greased on assembly — The unit goes in ready to run, so there is no extra greasing step during fitting.
Specification
| OE number | 85160-95J00 |
|---|---|
| Vehicle | Toyota Hiace (1983-1989) |
| Bushings | POM (DuPont grade) with brass bearings |
| Pivot arms | Aluminium, re-engineered design |
| Finish | Galvanised and coated, anti-rust |
| Mounting | Direct bolt-on to original points |
| Greasing | Pre-greased at assembly |
| Testing | 100% inspected before shipment |
| Packing | Neutral carton or customer-branded |
| Warranty | 12 months |
Symptoms this fixes
| Symptom on the van | What is worn | Does this part fix it? |
|---|---|---|
| Wipers barely move at all | Fully seized pivots | Yes |
| Arms out of step | Oval or hardened bushes | Yes |
| Knock per stroke | Pin play | Yes |
| Poor wipe only | Blades or arms | No |
Fitting outline
- Battery off; arms tape-marked.
- Soak the arm nuts; pull both arms gently with a puller.
- Cowl trim released carefully; brittle clips expected.
- Bracket unbolted; assembly out; crank transferred from the motor.
- New assembly fitted; bracket bolts evened.
- Arms to the marks; full cycle tested; park corrected.
Detail and photographs: replacing a wiper linkage.
Frequently asked questions
Can you supply this in bulk for distribution?
Yes. This is a volume part for the aftermarket and we supply importers, distributors and workshop chains with mixed container loads. Urgent orders are accepted and samples can be arranged.
What is the usual lead time?
Lead time depends on quantity and whether you need neutral or branded packing. Send us the quantity and your destination port and we will confirm the schedule in the quotation.
Do you cover other models from the same platform?
Very often yes — several vehicles share the same linkage. If you tell us the models you buy for, we will check the full cross-reference and bundle them into one shipment.
H50 or the later van — which one is mine?
By year: 1983-1991 is the H50 (85160-95J00); 1992-2004 is the later van (85160-95J03). The stamped number settles it.
Are these made new?
Yes — on our current line, with current-specification bushes and rods. That is why the reference is still worth buying for a working van.
Request a quote
Send us the OE number, the quantity you need and your destination port, and we will come back with price, MOQ and lead time. If you are sourcing a range of wiper linkages rather than a single part, ask for our full cross-reference list — we cover VW, Audi, Seat, Skoda, Ford, Toyota, Honda, Hyundai, Nissan and Opel applications.
Manufactured on our own line for a working classic — see our wholesale terms. Mechanism background: how a wiper linkage works.
Related wiper linkages and vehicle series
This Toyota Hiace 1983-1989 assembly is part of our Toyota Series wiper linkages range. Also stocked in the same series: Toyota Tacoma 1996-2004 wiper linkage (85150-04020) and Toyota Paseo 1996-1999 wiper linkage (85150-16520). For fitment guidance and fault diagnosis, see how a wiper linkage works. Every assembly ships with its OE cross-reference, so you can order by the number stamped on the old unit.






Reviews
There are no reviews yet.