Description
A replacement wiper linkage for the VW Golf 7 (2013-2020), cross-referenced to OE 5GG955023. Supplied as a complete linkage assembly, ready to bolt on without modification.
Uneven wiping, a blade that lags on one side, or a knock on every pass usually traces back to worn pivots rather than the motor. If the linkage is left in place, the extra load is passed on to the motor and gearbox.
Vehicles this wiper linkage fits
| Make / model | Model years |
|---|---|
| VW Golf 7 | 2013-2020 |
Replaces OE number: 5GG955023. If the number on your old linkage matches, this is the correct replacement.
Golf 7 (2013-2020): MQB-era linkage notes
The Golf 7 moved to the MQB platform, and its wiper linkage is a compact modern assembly that sits under a curved cowl with tight tolerances. On these cars the linkage rarely wears out early — most of the failures we see are water-related or impact-related, not cycle-related.
- Pressure washers are the enemy. Jetting along the cowl line forces water into the pivots; the failure is seized joints, not worn bushes.
- Cowl clips are single-use by design. They loosen on removal; keep replacements on hand.
- Service access needs the wiper arms off first. The assembly is extracted upward after the bracket is freed.
- Motor and crank stay on the car. Rods, pivots and bracket are supplied complete.
Confirm before ordering
| Check | What to look for |
|---|---|
| OE number | 5GG955023 on the old assembly — also 5GG955023 without suffix variants |
| Generation | 2013-2020 Golf 7. The Golf 6 takes 1K1955601 family parts; do not cross-order |
| Variant | Golf 7 shares platform parts with several MQB cars; the stamped number is the final word |
| Arm marks | Tape both arms at park before removal |
Why the original part fails
On a high-mileage vehicle the linkage outlives the bushings inside it. Once a pivot stiffens, every sweep pulls harder on the motor, and the wiper arm timing drifts out of position.
- POM bushings, DuPont grade — The original soft bushings wear oval and let the pivot move off-centre. A harder, dimensionally stable bushing keeps the clearance the linkage was designed with.
- Brass bearings at the pivot pins — Carries the load at the point where the factory part scores, so service life is not limited by a single wear surface.
- Aluminium pivot arms — Adds stiffness to the linkage under load — this is what stops the assembly flexing and skipping.
- Galvanised and coated steel — Water from the windscreen drains straight over this area. Coated rods and brackets resist rust and seizing in wet climates.
- Pre-greased on assembly — The unit goes in ready to run, so there is no extra greasing step during fitting.
Specification
| OE number | 5GG955023 |
|---|---|
| Vehicle | VW Golf 7 (2013-2020) |
| Bushings | POM (DuPont grade) with brass bearings |
| Pivot arms | Aluminium, re-engineered design |
| Finish | Galvanised and coated, anti-rust |
| Mounting | Direct bolt-on to original points |
| Greasing | Pre-greased at assembly |
| Testing | 100% inspected before shipment |
| Packing | Neutral carton or customer-branded |
| Warranty | 12 months |
Symptom to cause
| Symptom on the car | What is worn | Does this part fix it? |
|---|---|---|
| Wipers slow after a wash or heavy rain | Water-seized pivots | Yes |
| One arm lagging | Oval bush | Yes |
| Knock on reversal | Pivot pin play | Yes |
| Streaks with even arc | Blades | No |
Fitting outline
- Battery off; arms tape-marked.
- Arm caps and nuts off; arms drawn with a puller.
- Cowl panel removed; clips replaced as needed.
- Bracket unbolted; assembly lifted out; crank transferred from the motor.
- New assembly seated; bracket bolts tightened evenly.
- Arms refitted to the marks; cycle tested; park corrected if needed.
Full photographic procedure: how to replace a wiper linkage on your car.
Frequently asked questions
Do you cover other models from the same platform?
Very often yes — several vehicles share the same linkage. If you tell us the models you buy for, we will check the full cross-reference and bundle them into one shipment.
How do I confirm this VW Golf 7 linkage is the right part?
Match the OE reference 5GG955023 against the number stamped or printed on your original linkage. If your part carries a superseded number, send us a photo of it and we will confirm the match before you order.
Is the wiper motor included in this listing?
This listing covers the linkage itself. Several of our linkages are also available as a linkage-with-motor assembly — tell us the vehicle and we will quote both options.
Does this fit the Golf 6?
No — the Golf 6 uses the 1K1955601 family. The stamped number on the old assembly settles it in seconds.
Why did my Golf 7 linkage fail so early?
Almost always water ingress from cowl jetting, not wear. Keep high-pressure washers away from the scuttle line and the replacement lasts years.
Request a quote
Send us the OE number, the quantity you need and your destination port, and we will come back with price, MOQ and lead time. If you are sourcing a range of wiper linkages rather than a single part, ask for our full cross-reference list — we cover VW, Audi, Seat, Skoda, Ford, Toyota, Honda, Hyundai, Nissan and Opel applications.
Factory-direct, OE cross-referenced — see our wholesale terms. For the mechanism: how a wiper linkage works.
Related wiper linkages and vehicle series
This VW Golf 7 2013-2020 assembly is part of our VW Series wiper linkages range. Also stocked in the same series: VW Touareg 2005-2014 wiper linkage (7L0955601C) and VW Sharan 1995-2010 wiper linkage (7M1955603). For fitment guidance and fault diagnosis, see the complete wiper linkage replacement guide. Every assembly ships with its OE cross-reference, so you can order by the number stamped on the old unit.








Reviews
There are no reviews yet.